Відео

in 4 years the price boat only is up to 8,200

You mention you would go to a stainless prop, what one are you thinking about getting and what pitch? Would you do a review on it if you get one? I got the same motor and contemplating going to a ss prop too.

What frogs are being used

What kind of floor are you running

People, only watch this if you want to know what NOT to do. You're sprays should overlap. even from the initial primer coat he is leaving massive gaps & has to go back over it to get proper coverage. And then Uses acetone (paint remover) to clean after each coat. His final finish is the ultimate example of a rubbish job, The entire cowl was "orange peeled" when he put the cowl on the motor just before he put the decals on. It should have been polish smooth before he ever put the clear coat on. Watch any other video but this one!

Go 2 stroke much lighter

hah the rain and welcome to florida is so accurate

Very nice I’m getting ready to put a deck on mine

what gig you using

I will be ecstatic if I can get the results you did. I will be taking this project on later in the year. Right now I'm to wrapped up in learning how to repair gelcoat 😂. Already enrolled in the school of You tube for DYI boat engine repair and restoration 😅. I actually enjoy working on my boat so it doesn't bother me to learn and apply my new skills. When you finally get it right there's no better feeling. I can't thank guys like you enough for sharing your skills and teaching others like myself who really want to learn. I can't have a boat if I can't do the work. I'm an average person making an average wage trying to do a rich mans hobby 😂. You know what though I'm pulling it off. If you take your time and learn what to look for before you buy a boat you can find one that isn't ridiculously expensive and just needs some love. You have to want it! You have to love learning and doing your own work. If you do it's not break out another thousand it's break out a couple hundred and get ready to put in time and some elbow grease. Be ready to make mistakes and do it again sometimes to. My boat has come a long way and it's really starting to look awesome. I love knowing she's mine and I brought her back to beautiful with my own two hands and few ulcers😅.

I think you should have spooled the spinning reel with a mono backing instead of using 500 yards of expensive braid. That would still leave enough braid that you would never see the mono. In addition, attaching braid directly to the spool leaves too much chance for the braid to spin on the spool, even after filling the reel. But then again, the main purpose of the video was to trail the spooling device, which you accomplished.

Bro rod tip is fishing 101 nice vid I’m actually in Broward very cool

I am right handed but I very much prefer the handle on the LEFT side so I can cast with the RIGHT hand, and immediately start reeling if necessary. Maybe this is because I fish the majority of the time with a spinning reel or fly rod or cane pole or tenkara pole. But for a right hander, cast with the right hand. What now will the left hand do? It should do all the reeling. Right hand can apply thumb pressure to the spool if a bit of extra drag is needed. I always fish with a very light drag and use my thumb as needed, the RIGHT thumb, because I am holding the rod and palmint the reel with my RIGHT hand. Left hand does the cranking. Fine motor skills are not needed for cranking the handle. Righties, try it with left hand retrieve for a week and you will be hooked.

LOL HEAD AND SHOULDERS?! GTFO noob

I'm thinking to get a 1436 with 25hp jet for shallow water

What was length of boat

Merci beaucoup ❤❤❤❤❤

Nope. I've never forgotten. the plug. That would be pretty idiotic

14:15 Wow...no comments 😅😅

one time i had a peacock on, got him on land, he got off and flopped back in the water, went back to the bed, and ate again. Let's just say I got a picture with a peacock.

Do u have a 2in hitch?

When you had this motor, did it have a small squeal? At idle or slightly in gear. Goes away at higher RPM

Can you please tell me what floor you have in the boat and material?

Why is your motor missing so much

You have me kayak cred for having something you made. Pretty sweet

Doubles as a small cannon.

long chaft have yamaha no good , honda better boats- short

why couldent you use the heat gun to flare the end to fit the tiller handle instead of using the hacksaw and then use the one hose clamp to secure it thus getting your weight bias forward

Excellent video. Nicely produced... Thanks!

I used 2 shop vac extensions. 1 slides inside the other making the length i wanted. These are lighter than pvc, fit exactly over my tohatsu tiller. Do the pair of cut slits making it have the ability to be clamped tight. Already black.

Skip the acetone and use water and let it air dry USE THE TACK CLOTH BEFORE PRIMING and every time you sand..sand with 800 or 1000 grit wet/dry sandpaper, NOT the steel wool. MOST IMPORTANTLY....SPRAY IN AN AREA WITH GOOD LIGHTING...if you spray like he did in low lighting, it will turn out like crap like his did and not a smooth glass finish...good lighting will show your imperfections that need to be addressed and not spend all that money to say "I'm ok with it" or just to cover it up with a decal. A high quality gloss should look like a high quality finish, not like a gloss that looks like he used a 97 cent can of spray!

Short shaft motor ??

Put your gas and the batters up front

Do people ever throw rocks or stuff at you when you come to there docks and lights and try to take the fish they are trying to attract for themselves that seems kinda scumbaggy kinda like theft

frogs are best for snakeheads

NEVER shelter under a tree during a thunderstorm, Your chances of being struck is high

Is it easy to chage the fuel filter? you just screw it out and put in new filter?

Why not tohatsu? Their engined are lighter...any tips? Thanks!

how did this hold up? I'm looking at doing something like this or going the aluminum angle and rivet route. This looks so much more manageable for me and my skillset. I do have a foot controlled trolling motor that I need to mount. That deck looks perfect for that as long as I can secure it to the boat .

Can this paint and process apply to the rest of the outboard?

Awesome Tutorial, bumpppp!!

Whats the total weight of boat and trailer?

Nice boat, how much did it cost

This is impressive results. And the F25 is a compelling option if you're stuck deciding between a 20 and a 25 tiller, the Yamaha F25 is basically a strong 20 as it is a 2 cylinder design, it has less displacement (432cc) as the 3 cylinder brands (500cc) but more than the 20hp 2 cylinder options (>350cc). It is a true in between and offers the best combo of power and weight savings. I'd like to know what the fuel burn difference is compared to a Tohatsu 25 and see if having less displacement makes a difference (even though the Tohatsu is working less hard).

Great video

Just bought a 2003 Yamaha 25hp 4 stroke basically just like this one. Do you have like a amazon list of all the products you used there? Would be awesome just to order it all and get it shipped to me. Our local marina is outrageous on pricing.

great info , the brass crush washer , would you know the part number for that item ?

Beautiful motor

Awesome, simple, cost effective project, on a small functional boat , its all ya need to have a day fishing. Good job.

What scale is that?